Brick Paver Installation & Edging



Staging of product

A lot of paver projects will differ depending on gain access to, site conditions, job size and of course, the weather. These scenarios can have a general influence on your job from a timing stand point. Mindful consideration needs to be taken to figure out the time to start the paver installation. Constantly aim to avoid any traffic or lessen on the prepared locations.

The supervisor or project supervisor need to always have the products (sand/ pavers) distributed around the job website for effective and easy setups. Paver pallets/bundles should be put in a way not to interfere with the paver installation. The appropriate pallet/bundle placement can make the real project installation simpler and quicker by lowering the overall labor of managing the material.

Brick paver patterns

Pavers can be put in several patterns depending on their shape. Each paver shape will typically have numerous different hatch patterns that are supplied by the producer.

Specialists need to take into consideration the traffic weight loads on their paver jobs. In many applications worldwide, it has actually been revealed that pavers laid in a herringbone pattern have performed effectively.

Pavers that are 60 mm (2 - 3/8 in) density appropriate for pedestrian applications. Pavers that are going to be used in industrial or commercial applications ought to be 80 mm (3 - 1/8 in) in density.

Reference/starting point for brick paver installation

There are a variety of conditions that determine the starting point of a paver job.

When beginning to set up pavers it is best to snap a true straight chalk line on the surface of the bedding sand or pull a true straight string line above the surface area of the bed linen sand at the ended up elevation of the pavers This will help as a guide for maintaining straight joint lines and will also enable the installer to make changes in the positioning of the pavers.

Buildings and concrete curbing are usually not straight and ought to not be utilized for developing straight joint lines. The use of string lines is essential to identify the true straightness of the edge also. As the paver installation progresses, the string lines will help lessen the requirement for little trim pieces.

These will maintain a minimum joint width and enable the bedding and jointing sand to get in between each paver. Pavers with spacer bars are typically not laid in snug against each other since a string line will provide consistent joint spacing.

Installation of brick pavers.

One of the most widely used methods for the installation of pavers is hand installation of each paver. It is best to install a single row of pavers along one of the true straight lines that you have actually pulled or above the bed linen sand. The finest approach is to position a paver versus another one and let it move down into the bedding sand.

When installing pavers on a steep grade, they ought to be installed at the base of the grade going uphill. This will prevent the pavers from creeping as they are being laid.

The best method for setting up pavers on big jobs is to install them mechanically. There are a couple items a professional should consider prior to setting up pavers mechanically:

1.) Mechanical installers are only capable of installing pavers in particular patterns.

2.) The specialist needs to ensure that the producer is capable of manufacturing and bundling pavers in the wanted pattern on the pallets for simple mechanical installation.

3.) Specialists might experience a color blending situation coming off the packages of pavers Poor color mixing might result in a patchy looking installation. Most makers follow color mixing on each bundle of pavers, however it is the professional's obligation to ensure proper mixing in the field.

Cutting procedures for brick pavers.

Contractors normally have 2 ways of cutting pavers. Pavers are cut either by 1). A double bladed guillotine or by 2). A gas powered cut off saw or brick saw which is equipped with a diamond blade. The diamond blade cut-off saw or brick saw will offer a much cleaner and more accurate cut. The majority of brick saws will have a pipe accessory on them which will allow the operator to cut the pavers damp. When cutting pavers wet, it will help decrease dust and will extend the diamond blades life. The operator of the brick saw ought to always cut the pavers far from the surface of the paver field when cutting damp, due to that the pavers will create a slurry that will stain the paver surface area. Pavers that are cut must not fit tight, sufficient spacing should be readily available for jointing sand.

The brick saw operator needs to always wear the Koi Pond Florida correct security that is needed for running a saw, such as eye, ear, respiratory and hand defense ).

Edging types

Edge restraints play a significant role in the total success of an interlocking pavement installation Edging restraints remove lateral movement of the pavers and hold the pavers securely together. Particularly at the external boundary of the paver application, without an edging restraint, your project is ensured to fail with time.

Usually produced edge restraints are the most commonly utilized by contractors. Produced edging restraints can vary from, plastic edging, steel and aluminum, woods or precast concrete and stone.

Edging installation.

This could result in the migration of the bed linen sand and eventual lateral movement of the pavers. If there is a possibility of losing bedding sand in between the pavers and the edge restraint, then geo textile material is recommended. When a space in between the pavers and the edging exceeds 3/8" (10mm), then the area needs to be filled with cut pavers.

Compaction of brick pavers.

After installation, the pavers need to be compressed. The whole area that is to be compacted must be swept clean of any foreign items and particles that can trigger scratching or scuffing on the surface of the pavers.

In addition, it is essential that the very first compaction takes place prior to any jointing sand has actually been applied to the pavers. If jointing sand is applied to the pavers before compaction takes location, this can trigger a bridging problem and will not allow the joints to be totally filled with jointing sand. This can likewise avoid the pavers from being properly set into the bedding sand.

When compacting the pavers, it is suggested that you make a minimum of 2 passes in different directions across the pavers. This will enable the pavers to be effectively embeded in the bedding sand and will force the bedding sand up into the joints from the bottom of the pavers.

The compaction of the pavers is extremely important to the last performance of the pavers. Failure to do proper compaction can result in contortions and pavement failure gradually.


Paver pallets/bundles must be positioned in a way not to interfere with the paver installation. One of the most extensively used methods for the installation of pavers is hand installation of each paver. The operator of the brick saw must constantly cut the pavers away from the surface of the paver field when cutting wet, due to the truth that the pavers will develop a slurry that will stain the paver surface area. Edging restraints get rid of lateral motion of the pavers and hold the pavers firmly together. When a space in between the pavers and the edging goes beyond 3/8" (10mm), then the space should be filled with cut pavers.

Leave a Reply

Your email address will not be published. Required fields are marked *